Kawasaki OEM

Kawasaki OEM Cylinder Sleeve O-Ring Kawasaki KLR650

Cylinder Sleeve O-rings.

Kawasaki OEM Exhaust Gasket Kawasaki KLR650 (87-24)

Features: Stock OEM exhaust gasket Should be changed anytime the exhaust system is removed

Kawasaki OEM Exhaust Gasket Kawasaki ZX14R (06-25)

Kawasaki OEM Copper Exhaust Gaskets.

Kawasaki OEM Exhaust Gasket KZ900-KZ1000-KZ1100

This is a set of four exhaust gaskets that fit the 1976-1977 KZ900, 1970-1980 KZ1000, 1981-1983 KZ1000J and 1981-1983 KZ1100.  You need to replace the exhaust gaskets every time you take off...

Kawasaki OEM Exhaust Stud KZ900

*Fits Kawasaki 1976-1977 KZ900 These 6mm x 46mm studs are sold individually.

Kawasaki OEM Filter Bolt/Drain Plug O-Ring KZ900-KZ1000-KZ1000J

*Fits Kawasaki 1976-1977 KZ900, 1977-1980 KZ1000 and 1981-1983 KZ1000J

Kawasaki OEM Float Bowl Gasket Kawasaki KLR650

Features: Stock Gasket/O-ring Great to have for a spare if you're planning jetting changes Fits 87-13 Kawasaki KLR650

Kawasaki OEM Flywheel Rotor Bolt Kawasaki KLR650

Kawasaki KLR650 flywheel rotor bolt should be replaced anytime the flywheel is removed.

Kawasaki OEM Front Cam Chain Guide KZ1000 J

This is the stock OEM replacement front cam chain guide for the KZ1000 J model 1981-1984.

Kawasaki OEM Front Fuel Tank Dampner KZ900-KZ1000

*Fits 1976-1977 KZ900 and 1977-1981 KZ1000 These rubber dampers fit on the round studs on each side of the frame and the gas tank slides over them. Two are required per bike.

Kawasaki OEM Head Gasket Kawasaki KLR650

Stock OEM Head Gasket from Kawasaki

Kawasaki OEM Kickstarter Cover Seal KZ900-KZ1000

*Fits Kawasaki 1976-1977 KZ900 and 1977-1980 KZ1000

Kawasaki OEM Large Rubber Dampner KZ900-KZ1000

This is the large rubber dampner that go between the cylinder and the engine case.  Two are required per engine.

Kawasaki OEM Left Side Carburator Holder KZ900-KZ1000

This is the left side carburator holder for the 1976-1980 KZ900-KZ1000.  These fit the stock 26mm or 28mm carbs and the aftermarket 29mm Mikuni carbs only. If you have Mikuni Flat Slides,...

Kawasaki OEM Oil Fill Cap O-Ring KZ900-KZ1000-KZ1000J

*Fits Kawasaki 1976-1977 KZ900, 1977-1980 KZ1000 and 1981-1983 KZ1000J

Kawasaki OEM Oil Filter Plug O-Ring KZ900-KZ1000-KZ100J

*Fits Kawasaki 1976-1977 KZ900, 1977-1980 KZ1000 and 1981-1983 KZ1000J

Kawasaki OEM Oil Filter ZX-14R (06-25) ZX-10R (04-25) ZX6R (95-25)

Make - Model - Year K&N Filter Hiflofiltro Fram FLO Billet Stock OEM Parts Ult. BMW S1000RR...

Kawasaki OEM Oil Galley Plug O-Ring KZ900-KZ1000-KZ1000J

*Fits Kawasaki 1976-1977 KZ900, 1977-1980 KZ1000 and 1981-1983 KZ1000J

Kawasaki OEM Oil Level Window KZ900-KZ1000

*Fits 1976-1977 KZ900 and 1977-1980 KZ1000 This oil level window mounts in the clutch cover.

Kawasaki OEM Oil Pan/Breather O-Ring KZ900-KZ1000-KZ1000J

*Fits Kawasaki 1976-1977 KZ900, 1977-1980 KZ1000 and 1981-1983 KZ1000J

Kawasaki OEM Oil Passage O-Ring KZ900-KZ1000-KZ1000J

*Fits Kawasaki 1976-1977 KZ900, 1977-1980 KZ1000 and 1981-1983 KZ1000J

Kawasaki OEM Oil Pump O-Ring KZ900-KZ1000-KZ1000J

*Fits Kawasaki 1976-1977 KZ900, 1977-1980 KZ1000 and 1981-1983 KZ1000J This is the 42mm V-ring that goes between the engine cases and under the oil pump. You need two per engine. 

Kawasaki OEM Outer Clutch Plate Kawasaki ZX-14R (12-25)

Kawasaki OEM Outer Clutch Plate for the Kawasaki ZX-14R (12-25)

Kawasaki OEM Pan Head Screw KZ900-KZ1000

This is the 6x10mm pan head screw that is used to install the KZ900-KZ1000 cam chain guide. 

Kawasaki OEM Piston Ring Set Kawasaki ZX14 (06-11)

Stock OEM Piston Ring Kit for 1 piston.

Kawasaki OEM Piston Ring Set Kawasaki ZX14 (12-25)

  Stock OEM Piston Ring Kit for 1 piston.

Kawasaki OEM Point Base Seal KZ1000J

*Fits Kawasaki 1981-1983 KZ1000J

Kawasaki OEM Point Base Seal KZ900-KZ1000

*Fits Kawasaki 1976-1977 KZ900 and 1977-1980 KZ1000

Kawasaki OEM Rear Cam Chain Guide KZ1000 J

This is the stock OEM replacement rear cam chain guide for the KZ1000 J model 1981-1984.

Kawasaki OEM Rear Tank Rubber Dampner KZ900-KZ1000

*Fits 1976-1977 KZ900, 1977-1981 KZ1000 Two of these dampers are required per bike.  They go over the frame rails.

Kawasaki OEM Right Side Carburator Holder KZ900-KZ1000

This is the right side carburator holder for the 1976-1980 KZ900-KZ1000.  These fit the stock 26mm or 28mm carbs and the aftermarket 29mm Mikuni carbs only. If you have Mikuni Flat Slides,...

Kawasaki OEM Rubber Cam Chain Roller KZ900-KZ1000

*Fits Kawasaki 1976-1977 KZ900 and 1977-1981 KZ1000 This is the roller that goes between the cylinder and the engine cases. If it is "Hard" or "cracked"; you need to replace it before it shatters...

Kawasaki OEM Shift Shaft Circlip KZ900-KZ1000

This is the 12mm circlip that goes on the end of the shift shaft on 1977-1980 KZ900-KZ1000's and 1981-1983 KZ1000J's.

Kawasaki OEM Shift Shaft Seal KZ900-KZ1000-KZ1000J

*Fits Kawasaki 1976-1977 KZ900, 1977-1980 KZ1000 and 1981-1983 KZ1000J

Kawasaki OEM Side Cover Grommet KZ900-KZ1000

*Fits Kawasaki 1973-1980 KZ900 & KZ1000 You will need 6 of these for a full set, there are 3 for each side.

Kawasaki OEM Small Shift Fork KZ900-KZ1000

*Fits Kawasaki 1976-1977 KZ900 and 1977-1980 KZ1000

Kawasaki OEM Tach Drive Seal KZ900-KZ1000

*Fits 1976-1977 KZ900 and 1977-1980 KZ1000

Kawasaki OEM Tachometer Drive O-Ring KZ900-KZ1000

*Fits Kawasaki 1976-1977 KZ900 and 1977-1980 KZ1000 This goes on the tach drive piece, that slides into the hole on the front of the cylinder head.

Kawasaki OEM Tank Strap KZ900-KZ1000

*Fits Kawasaki 1976-1977 KZ900 and 1977-1980 KZ1000

Kawasaki OEM Top Idler Assembly Kawasaki KZ900

*Fits Kawasaki 1976-1977 KZ900 This is the top idler assembly that sits directly on top of the cylinder head, four bolts hold it in place.

Kawasaki OEM Top Idler Rubber Dampner (Thick) KZ900

This is the top idler rubber dampner that fits the 1976-1977 KZ900.  This is the thicker one.

Kawasaki OEM Top Idler Rubber Dampner (Thin) KZ900

This is the top idler rubber dampner that fits the 1976-1977 KZ900.  This is the thinner one.

Kawasaki OEM Transmission Bearing Cap O-Ring KZ900-KZ1000

*Fits Kawasaki 1976-1977 KZ900 and 1977-1980 KZ1000 This is the tiny 7mm o-ring that goes inside the bearing cap.

Kawasaki OEM Transmission Bearing Ring KZ900-KZ1000-KZ1000J

*Fits Kawasaki 1976-1977 KZ900, 1977-1980 KZ1000 and 1981-1983 KZ1000J  It is the half moon ring that locks the bearing into the cases. There are two of them in each engine.

Kawasaki OEM Transmission Shaft O-Ring KZ900-KZ1000

*Fits Kawasaki 1976-1977 KZ900 and 1977-1980 KZ1000 This is the o-ring that slides over the transmission shaft in front of the bearing.

Kawasaki OEM Two Step Clutch Lever Replacement Switch KZ900-KZ1000

This is the replacement switch that goes on the two step clutch lever; part number 46076-1105.

Kawasaki OEM Valve Seal KLR650-KZ900-KZ1000-KZ1000J-GPz1100

*Fits Kawasaki 1987-2020 KLR650, 1976-1977 KZ900, 1977-1980 KZ1000, 1981-1983 KZ1000J and 1983-1984 GPz1100 Sold individually

OEM Clutch Inner Hub Kawasaki ZX-14 (06-11)

Kawasaki ZX-14 OEM Inner Clutch Hub Direct Replacement Perfect if you are wanting to purchase an MTC Enginnering Mullistang Stage 2 clutch and need a Kawasaki ZX-14 (06-11) inner hub to send them...

OEM Kawasaki ZX-14R Service Manual (06-25)

  Kawasaki ZX-14 OEM Service Manual Years 2006-2024

OEM Speed Sensor Kawasaki ZX-14 (06-11)

Geniune OEM Part in Brand-New Condition Fits Gen 1 Kawasaki ZX-14 (2006-2011)