- All Electrical
-
Batteries
- Battery Chargers/Accessories
-
Connectors and Wiring Harnesses
- All Connectors and Wiring Harnesses
-
Connectors by Application
- All Connectors by Application
- Ambient Air Pressure Connectors
- Cam Position Connectors
- Coil Connectors
- Crank Position Connectors
- Dash Connectors
- ECU Connectors
- Fuel Injector Connectors
- Fuel Pump Connectors
- Gear Position Connectors
- Handlebar Control Connectors
- Ignitor Connectors
- Inlet Air Temp Sensor Connectors
- Manifold Pressure Connectors
- Radiator Fan Connectors
- Tail Light Connectors
- Throttle Position Connectors
- Turn Signal Connectors
- Connectors By Number of Ways
- Custom Wiring Harnesses
- Delete/Disable/Eliminate
- Engine Wiring Harness
- Extension Harnesses
- Fuse/Circuit Breaker
- Fuel Pump Jumpers
- Gauges
- Power Distribution
- Regulator/Rectifier
- Relays
- Sensors
- Shift Lights
- Switches
- All Engine
- Bearings & Fasteners
- Camshafts & Tensioners
- Crankshaft & Rods
- Cooling System
-
Gaskets & Seals
- All Gaskets & Seals
- Exhaust Gaskets
- Seals & Dowel Pins
-
All Gaskets
- All All Gaskets
- Honda CBR1000RR
- Honda CBR954RR
- Kawasaki KLR650
- Kawasaki KZ900/1000
- Kawasaki Ninja 1000
- Kawasaki ZX-10R
- Kawasaki ZX-11
- Kawasaki ZX-12
- Kawasaki ZX-14R
- Suzuki GS1100/1150
- Suzuki GS750
- Suzuki GSXR1000
- Suzuki GSXR1100
- Suzuki GSXR600
- Suzuki GSXR750
- Suzuki Hayabusa
- Yamaha FJ1100/1200
- Yamaha YZF-R1
-
Lubrication System
- PAIR Block Off Plates
- Pistons & Rings
- Diapers / Restraints
- Starter Components
- Transmission
-
Valve Train
- All Hardware
- Hardware Kits
- OEM Hardware
-
Titanium Hardware
- All Titanium Hardware
- Air Shifter Mount Bolts
- Cam Chain Bolts
- Cam Cover Bolts
- Clutch Hub Nuts
- Engine Mount Inserts
- Front Sprocket Nuts
- Hardware Kits
- Header Bolts/Studs
- Kickstand Bolts
- Oil Galley Plugs
- Pressure Plate Bolts
- Seat Bolts
- Sprocket Nuts
- Stator Bolts
- Swingarm Pivot Axles
- Swingarm Pivot Links
- KLR650
- KZ900-1000-J-GPz
- Ninja H2
- ZX-10R
- ZX-12R
- ZX-14R
- Hayabusa
- GS1100-GS1150
- GSXR1000
- GSX-8R
- GSXR750
- GSXR600
- YZF-R1
- YZF-R6
- Batteries
- Battery Chargers/Accessories
-
Connectors and Wiring Harnesses
-
Connectors by Application
- Ambient Air Pressure Connectors
- Cam Position Connectors
- Coil Connectors
- Crank Position Connectors
- Dash Connectors
- ECU Connectors
- Fuel Injector Connectors
- Fuel Pump Connectors
- Gear Position Connectors
- Handlebar Control Connectors
- Ignitor Connectors
- Inlet Air Temp Sensor Connectors
- Manifold Pressure Connectors
- Radiator Fan Connectors
- Tail Light Connectors
- Throttle Position Connectors
- Turn Signal Connectors
- Connectors By Number of Ways
-
Connectors by Application
- Custom Wiring Harnesses
- Delete/Disable/Eliminate
- Engine Wiring Harness
- Extension Harnesses
- Fuse/Circuit Breaker
- Fuel Pump Jumpers
- Gauges
- Power Distribution
- Regulator/Rectifier
- Relays
- Sensors
- Shift Lights
- Switches
- Bearings & Fasteners
- Camshafts & Tensioners
- Crankshaft & Rods
- Cooling System
- Gaskets & Seals
- Lubrication System
- PAIR Block Off Plates
- Pistons & Rings
- Diapers / Restraints
- Starter Components
- Transmission
- Valve Train
- Hardware Kits
- OEM Hardware
- Titanium Hardware
Air / Electric Shifter
Air Shifters are used to allow fast mechanical shifts with the use air.
A shift cylinder is attached to the motorcycle shift mechanism either by the shift lever directly, or by an additional bracket. A solenoid valve controls the air supply to the shift cylinder via the compressed air source, such as an air tank in the swingarm/chassis or a regulated high pressure supply. When the rider wants to make a shift, a button is pressed that gives a signal to the solenoid to open. This causes the compressed air to enter the shift cylinder and push or pull on the shift mechanism just like the rider's foot normally would.
Another key component that is required is an engine power cut. This is commonly called a "kill box". This works by momentarily cutting the ignition or fuel supply to the engine for a very brief period of time (30-90ms) while the air shifter is activated. This allows the transmission to shift into gear without the use of the clutch.
Since all shifting is done with an electronic signal, you can can wire the bike to automatically shift at a preset RPM with the use of an RPM activated switch or a shift light with autoshift output
Most riders prefer to use the stock horn button as their air shift activation, which is perfect since Schnitz Racing offers wiring harnesses and instructions on how to do that.